|
|
原文如下，不过比较长，怕大家烦哦，0 c- j6 R" l5 I) @$ p0 i+ E
Notes3 c7 o8 C4 G& p2 I7 L& a0 \/ N
1. The pro-engineer model/file &the iges file generated from this model, contain the master information for this part
3 k: s! q n% t5 Y) p% HDesign changes must be made to the pro-engineer model.
) U8 o2 V" H9 ~3 X% gThe iges file & autocad drgs must be updated & up-issued accordingly….
+ I! a, r0 P5 ?) ^ ~2. Demensions are for reference only (refer note 1)3 W( c, W+ Q% p, A9 F# K4 g k/ |
Dimensions are from top of the draft unless otherwise shown- [; c2 v0 w3 o7 t. t. g, n5 l' J4 d
3. Drafts angle……
) V$ L' z0 ]+ B) a [$ Q4. Casting radll:
! @9 l" X! p) C s7 Z& T$ _ l1 n1)…fillet/radll
* w+ E7 w3 @" T# A2 U$ ]2) sharp edges/ d: h5 j& e! c3 t0 L. N$ w% c% m
5. Casting to be of uniform density with no visual or linked porosity. g7 Z3 N; _' p+ \) |
6. Sealing faces:
* A, a6 x0 D9 x+ BArea around holes or openings & faces marked: to be flat & free from protrusions, split lines & imperfections.
i+ i# {! `- L* N+ p7. Geometry tolerances:7 E4 K' z$ K7 p( s
1) General flatness/squareness/parallelism-0.5
) q7 a0 A$ n) m8 N9 L2) Boss surfaces & sealing faces% [+ u5 T" h n8 M4 |9 ]* Z
Flatness/squareness/parallelism-0.2
$ n7 F- C# h0 o8 p* I1 Z9 g8 B* P8. Surface finish:2 p5 ^, F; `" `, |" q+ u3 u
1)as cast 1.6 or better8 }9 h) ]) Q# E Z" Y9 V( O8 [
2)no cold flow marks
3 r b% Y; k0 e% O4 O: K, {% ?3)no drag marks or galling6 z. Q& S4 O9 D! F+ {$ C
4)part lines & holes to be flash free9 m) N4 w! x) i. g: N
5)remove all burrs & sharp edges5 w8 w2 u2 D4 l
9. Rear panel. Rf chassis, gaskets and covers to fit together as designed, V3 H" k) r% V
10. Assemble 1×screw, M4×12 pan slotted, stainless steel, and 2×washers,4mm normal, stainless steel, to M4 tapped hole, torque 1.4Nm* X: H9 `2 ~0 H
, N4 y; Y6 a, @( b! eNotes2
& ]1 v; H9 _) m% }8 k7 s1.alodine to codan spec01-00931' k$ h6 n/ Q) j7 Z$ C
2.mask areas shown hatched
$ A" F5 R# u9 |5 }3.ensure all edges of holes & cutouts are painted
" C! y9 c9 A% N1 W6 `7 G2 L$ u5 ~4.paint crodalux powder coating-HT531/5114, hybrid texture,4 I' \5 m9 b0 B" @% L7 `
colour：rolling thunder (dark charcoal)
$ d& O) M: K; I: A to codan spec 0100097 process s& P! F8 G9 B6 z% p
, E+ Q- e5 a$ a! d4 ?( \1 K1 h
% p6 N2 Y& K2 n ~我来翻译一下:$ Y. X. J. E+ u- f: S" H
1 K# f0 ^" r1 A# C, g: N
Notes0 Y3 M" X% e: Q% f% ~ L
4 p- S2 v" Z% b+ O A( `1. The pro-engineer model/file &the iges file generated from this model, contain the master information for this part, G0 {, W6 C7 T9 R
Design changes must be made to the pro-engineer model.- S# U4 `& v# J! K% k
The iges file & autocad drgs must be updated & up-issued accordingly….
' H( B6 l' V0 `! N# B2 |. }
) K8 d8 V8 ]% W9 a& T; ?& P+ Z破衣模型/文件 和 IGES文件 都是从这个模型上产生的, 包含这个零件的主要信息!6 c* c, i. w- P t
设计变更必须在破衣文件上更改
6 s& j8 `+ e2 ~$ ~& WIGS文件和CAD图必须依据变更及时更新和发行.
, {6 ~( b: Y. {! G/ K) R9 J* Y
, h' Z$ l* d6 D- u8 P2. Demensions are for reference only (refer note 1)
% ]! D! ?+ [; E- }; J6 V$ TDimensions are from top of the draft unless otherwise shown
. {* I0 A2 g4 Z2 D8 @' {
. m8 c. p/ c! U. x( d' V# C尺寸仅做参考(参考Note1)
6 A. G7 A% B/ I2 {尺寸标示除特殊说明,都是指拔模大端尺寸
% J2 N8 Y: j* R- b9 b p6 T; ^9 o( r: |9 R0 `/ @, M5 o6 V6 |& w
3. Drafts angle……7 L3 M" [7 [' i0 m% g- p
* r6 r1 ]" a3 h0 y0 y拔模角
' ^8 X/ `" M5 n7 t0 Y! K b6 Z3 o
7 ?( @5 k; V4 y [$ e1 ^4. Casting radll:% U) e$ n% ?6 w7 f
1)…fillet/radll
' _9 ]% n8 [/ Y% d J2) sharp edges: s' C# {, ?: p' {, j: b6 _- S
- s: U1 Y, o" Y- s* x铸造圆角. X* |. b) A! b9 P! O% n) E
1>圆角半径
6 }! b9 z p) r9 Q6 y4 E4 |: ^, r2>锐边. p3 ~+ G4 _0 G; Z+ ^
% \* R2 M7 t5 u' s& |5 l2 `, o5. Casting to be of uniform density with no visual or linked porosity; ~8 a! v/ T+ v
1 E6 a2 E2 n4 E' |- Q8 p应铸造成密度均一, 没有可见的或连贯的沙孔" f: B7 w; N5 ]- Q! N1 X; b0 i
, ]! \/ P Q( Y5 ]$ T6. Sealing faces:+ z$ m; @& t: ^
Area around holes or openings & faces marked: to be flat & free from protrusions, split lines & imperfections.' a8 a6 Z0 h/ J$ X+ ?6 B2 }8 N
1 q% o) G) e% D
密封面5 B3 U6 j3 w. P8 g3 O) U
孔,开口或者尖锐面周围要求: 平,无突出,无断裂线或者不完整6 m! N3 r; ~4 J7 i
" O' V/ O/ W2 K7. Geometry tolerances:
. K! E& s, C1 O: b1) General flatness/squareness/parallelism-0.54 F7 R+ R/ U1 g- K s. a
2) Boss surfaces & sealing faces
" W' M: E1 X" Q Flatness/squareness/parallelism-0.2
1 L2 k* L0 l! [, s6 _! G1 h! b4 W t ?$ W6 G- h3 @
几何公差3 z8 o* ^$ w Z4 g
1. 平面度,垂直度,平行度 通规0.5, C) i H. C9 I8 j7 h
2. 圆柱表面/密封表面
& @2 o& t4 i2 F$ J- W- b4 g# U平面度,垂直度,平行度 0.2$ Q3 f* M# Q" e7 \* B
4 }9 X9 a) i* B7 p8. Surface finish:
5 x: T4 T1 e, ~3 _2 o1)as cast 1.6 or better
. p0 g. W4 S! z6 B2)no cold flow marks" c' J4 X$ t8 v$ b
3)no drag marks or galling" Y& n2 W7 j0 ~! L5 x) [
4)part lines & holes to be flash free
7 B7 L* i" A) u* }& z5)remove all burrs & sharp edges
6 ]* h6 g( K) z( j& U" `: `. F, h
1 U. I9 o: a, `表面处理
8 F! o& E {# G, {9 d( }表面粗糙度1.6或者更高: R0 \! w+ R4 y1 k
没有冷流痕
8 Y$ g" Z: m, Y没有拉伤痕迹或者擦伤
- h( F, b$ b* x" ]
1 i9 l" {; Y- c& ?2 P5 r9. Rear panel. Rf chassis, gaskets and covers to fit together as designed( d9 E" `5 q' B1 ?9 }* R& r9 u4 \
/ X( i" y d4 X" R5 F) q$ v8 Z0 ~# J$ O后板, 模框, 垫圈和外盖必须依照设计装配在一起.3 c& d9 ^/ a- q4 _
! l' g6 S3 ?, }1 d% L1 ~% B5 f% i
10. Assemble 1×screw, M4×12 pan slotted, stainless steel, and 2×washers,4mm normal, stainless steel, to M4 tapped hole, torque 1.4Nm1 M6 v- t7 N4 |9 Q
& f! E9 i, \. f" S% x. S
安装一颗M4*12的平头带槽的不锈钢螺丝, 两个通常4mm厚的不锈钢垫片两个
7 o: R( g, K' e3 J
& J7 w9 K/ r2 q) M& fNotes23 z" t% l' w) a; u/ ], y
1.alodine to codan spec01-00931
K; Y* `+ s! o6 X2 ~必须遵从01-00931规格
y3 _+ _1 Q3 L6 t, K {- R& v
* D) u9 C _6 r" C+ Z" x7 y* G2.mask areas shown hatched2 _/ y9 N6 ?" A j3 a* n$ J6 q' d
遮蔽区域应该以剖面线显示; C8 p2 {- B h: {" d- O9 A) _9 C
' u% T( w. e7 `+ g7 @; Y3.ensure all edges of holes & cutouts are painted
: q& C0 u" d. W# G' w, K- j1 g7 i- G5 g
取保所有孔以及切口的边线着色显示+ E' @2 x+ X- c; d9 z t2 `6 S
! A/ o0 x- @- }' m# }/ s
4.paint crodalux powder coating-HT531/5114, hybrid texture,% @+ P( ? u. W1 t5 P3 ]
colour：rolling thunder (dark charcoal), s' `/ ?/ q/ `5 e/ U) H7 {
to codan spec 0100097 process s/ R1 r }/ a1 a$ _# m
喷Crodalux粉体层,型号HT531/5114, 混合纹理./ k9 b+ U" C% P- _; s2 z
颜色: 雷声(碳黑色)6 y2 c a9 R- y# ^) N9 m' j2 M7 D
遵从0100097工艺规格
7 z6 _- q$ S* L" k: K) x; u4 {6 h9 o# Q0 R
' d3 X, ]7 A v% n9 W$ R7 E: p6 X6 m7 b6 E8 c/ A2 E. ^; x
powder coating是粉末喷涂，和喷漆不太一样
( @" B5 a+ p2 h2 x0 ~. f什么“破衣”，这个不要翻译，proe是3d软件！ i* a1 O1 e9 X7 M h* K& [
powder coating是喷粉的意思，是在工件表面均匀地喷上所需颜色地粉末，然后经高温烘烤附着在工件表面。 |
|
发表于 2008-3-29 10:20
发表于 2008-3-29 10:45
楼主